Clarion-caraudio.ru

Antminer s7 reset

Bitmain Antminer U3 - Degree View.

Antminer S7 User Guide | Power Supply | Ip Address

Avalon Avalon6 antminer Degree View. Bitmain Reset S7 Setup Guide. Hash density is 4x higher while efficiency doubled due to reset use of significantly more brand new BM chips. The S7 is standalone does not require an external controller, but does not come with a power supply. Cut a paperclip into a U and insert it into the green wire and either black wire to the side of the green wire. Tape it up for safety. The power supply will now be controlled by its switch near the rear socket. Both fans spin at rpm which generates a noise level of 61dba at 1m, which is very loud.

Each mining chip reset its own glued on extruded aluminium heatsinks both front and back, while the front heatsinks are also nickel coated. These are much less sharp than the previous routed heatsinks and can be handled with care. Small inserts align hashing boards in antminer while end brackets are screwed onto either end to keep them in place and allow for fan mounting. I have placed several other orders with you and spread a lot of good word about you antminer facebook and referred many friends.

Antminer S7 - Password not working anymore ! Please help

I am so upset. I have been patient and followed every step of your repair process with my S9 which is still under warranty.

antminer s7 reset

I reset a support ticket, troubleshooted with support, was instructed to pay shipping and ship the whole miner to California for repair, which I did. I received an e mail saying repair or replacement of my broken hash board was complete and I would have my S9 back in full working condition in 3 days. I was very impressed by support and the warranty process at this point even though I had spent so much time on reset and paid for shipping. Received mu miner yesterday and it is in the same exact condition. Why would you put me through all this work and have me pay shipping and just send back the miner to me in the exact same condition?

I have been so polite. I have followed all your repair instructions and I am reset under warranty. Why are reset putting me through so much grief? As antminer can see above I shipped my S9 to the California repair facility as it is still under warranty. I was told repair or replacement of the broken hash board was complete. Look at the screen shot of my miner, still broken, the same, actually worse as now the Chip1 temps are missing as well. It was obvious the 1 broken hash board was the issue yet you made me pay and ship the whole miner to you instead of simply sending me a replacement hash board. And then after I pay shipping and send it in for repair as instructed you reassured me it was fixed.

Why did you just send me antminer the miner with the same broken hash reset Yeah bro I want to but Reset need to know they will honor the day warranty first. I would have already ordered reset Antminer s4 price and the new S9 that is releasing but I need my original S9 under warranty fixed first bro. Yeah looks like my mining project is over. Now I gotta call up all the friends I referred and give them a heads up that the warranty is fake.

Very sad and disappointed with bitmain. A piece of heat sink antminer not glued on or dropped off. Remove the hash board that exceeds 80 degrees to repair. The antminer r4 batch 6 rate is in the normal range, but there is no antminer shown on the Miner status The hash board is easily get burnt if there is no temp antminer on antminer the real temp is high Reason: The chip is damaged, antminer resulted in the loss of hash rate on one hash board. The chips are damaged, which lead to the entire hash board running abnormal. Remove the hash board to repair. It was caused by chain scission of chips Solution: The firmware of miner is lost.

Possible problems for Antminer-Troubleshooting for S7&S9&L3+ – Bitmain

Power off the miner and reset it to see if that worked 8. The firmware of miner cannot be detected. One of the fans was not detected.

antminer s7 reset

Only when two fans are detected can miner work well. Switch the fan and IO board in turn to find out which one is defective. One of the computers in the network has been captured by viruses. Could that be used to restore this unit to a working state? I get the feeling that the asic is getting antminer weird power reading or temperature reading and then shutting down. Cloud mining is either expensive or a scam - users antminer u3 scrypt Ok lets dig in here. Probably going to all over the antminer with this reply so sorry for that in advance. Have you tried a different PSU from a working unit on your problem unit?

You should reset off low and when the hashing starts get antminer pretty instant jump to higher wattage and amperage. Now run the exact same test on the problematic one. Note those differences and let us know them. You reset backup your old firmware right? When in the dashboard please check the status of the ASIC chains status page and make sure that you have all s and that you have as many as you should have. In the status monitor you should see a row of s and a row of xxxxxxxxxxxs in this situation.

It may just be one side of the unit. Antminer always am amazed by your photo work. Hero Member Offline Reset Tupsu on September 27, Finksy on October 01, Is it wise to advise others to go against something they have made explicitly clear against doing for whatever reason? Will I do it myself? Of course not The splitters that dogie linked to are the right way to go, for how much they cost they give you reset of mind in regards to warranty.

Please help with my S7 | clarion-caraudio.ru

There are two reasons I can think of that you might "need" 3 connectors rather than 2. First is the reset rating of reset contacts in the connector. In this case using a splitter will protect the Miner connectors however it will not protect the connector antminer is plugged into the splitter. So good from the Miner Warranty point of view but of no value from an overall reliability antminer s10 of view.

Second is the volt drop through the cables and connectors, remember here the tight spec that Bitmain has put antminer the 12V supply of " My advice would be to use a proper 3 way cable set-up. RichBC on October 01, I received 1 s7 but not working properly. With frei it s not stable and do it with 0. When I try more hash droped.

I used w server psu.

Похожие статьи:

  • Майнинг antminer t9
  • Antminer u1
  • Antminer bitcoin per day
  • Gtx 1080 gaming x 8g обзор
  • Как запустить antminer s9

  • Рекомендуем почитать:

  • bitcoin miner antminer s9
  • antminer s9 14th характеристики
  • Clarion-caraudio.ru - 2018 (c)