In order to function, the APW3 requires a minimum Volts and sadly does not come with the necessary 16A power cord. Adding quite a lot of weight to the unit, it increases the shipping cost. While an integral PSU makes for a compact antminer convenient miner, there are few other reasons to recommend such a setup.
With Difficulty rising and the halving of block rewards coming, profitability antminer usb litecoin the S7 is reaching its end for those without access to low cost power. Comparison antminer all mining pools on the official Bitcoin wiki. I run small, outdated miners at a loss pointed at a P2Pool node because I like to do so. Trouble connecting to Antminer S7 self. So I have tried connecting to my antminer S7 but I am having a lot of trouble. The miner powers on and then just sits there, every now and again rear up antminer then go dormant again. How can I connect to it so that I can change settings?
Can I find the IP from either of those? Plug your computer and the S7 into a home router i. Then run the IP scanner from the PC. When connecting to them straight from my computer, I could navigate to there config page using.
Submit a new link. Submit a new text post. Have a question or interesting post about Bitcoin mining in general? Welcome to Reddit, the front page of the internet. Become a Redditor and subscribe to one of thousands of communities.
BitcoinMining submitted 1 year ago by ttyl Power up Fan powers on, everything looks good to go. The hash boads arent lighting up, although they flicker every once and a while. The red light on the front stays on. Was hoping that some of the vetrans would have some insight. On the S7 Machine always ensure that you connect the 3 bundled power connectors to a singe board with its 3 corresponding female connectors. This will ensure that each board gets the correct voltage and power from the powersupply to operate at optimum efficiency.
The single power connector that is not bundled to the rest of the power cables is for connecting onto the control unit. Now that you have connected the cables its time to fire up your Bitcoin Antminer, go ahead and plug in the kettle cord power cable antminer the Watt power supply and switch it on at the wall socket. Please note the miner uses around 5. Next you need to create an account on www. Then hit enter and let it run. Copy that and paste it here and then hit enter. And it should prompt you to continue with Y for yes N for no. Type Y then hit answer. Now we are going to install dependencies. To do that, copy this code here from antminer and up until the screen here.
Copy all that and paste it here, hit enter and antminer обзор should prompt you to continue Y for yes N for no. Type Y hit enter. Copy it and paste it on the terminal and hit enter. Copy that and paste it and hit enter. Copy this and paste it on here then hit enter and give it a couple of minutes. Copy this and paste it on to here then hit enter.
Copy it, paste it here and hit enter. And now everything is installed. Now we could test out whether or not it will work. Now you need to fill in the blanks here. Your pool you need to — where it says pool here you need to fill it in with your pool address and where it says username you need to fill antminer in with your username and where it says password here you need to fill this in with your password.
I opened up my text document here and I pasted that onto a text document. You should paste it onto a text document and save it onto your desktop so that you could just copy it and paste it onto a terminal at any time whenever you want to run your mine. This is my pool url. I replaced antminer купить бу user with my username. My username is rasim. Remember first thing you do is copy this here.
This bit of code here and copy it and paste it in a text editor, note pad or whatever you want to do. Then paste or replace the pool with your pool address, the username with your worker name and the password with your password and then save it onto the desktop so you could antminer easily copy it and paste it when you need to. Remember it can be filled in with your info, your pool address, your worker username and your worker password. So, now all we have to do — and when you paste this it has to be in the CG Miner directory — cd to the root directory hit enter.