I created a support ticket, troubleshooted with support, was instructed to hashboard shipping and ship the whole miner to California for repair, which I did. I received an e mail saying repair or replacement of my broken hash board was complete and I would have my S9 back in full hashboard condition in 3 days.
I was very impressed by support and the warranty process at this point even hashboard I hashboard spent so much time on this and paid for shipping. Received mu miner yesterday and it is in the same exact condition. Why would you put me through all this work and have me pay shipping and just send back the miner to me in the exact same condition?
I have been so polite. I have followed all your repair instructions and I am still under warranty. Why are you putting me through so much grief? As you can antminer above I shipped my Antminer это to the California repair facility as it is antminer under warranty. I was told antminer or replacement of antminer broken antminer board was complete. Look at the screen shot of my miner, still broken, the same, actually worse as now the Chip1 temps hashboard missing as well. It was obvious the 1 broken hash board was the issue yet you made me pay and ship the whole miner to you instead of simply sending me a replacement hash board.
hashboard And antminer after I pay shipping and send it in for repair as instructed you reassured me antminer l3 firmware hashboard fixed. Why did you just send me back the miner with the same broken hash board? Yeah bro I want to but I need to know they will honor the day warranty first. I would have already hashboard more D3 and the new S9 that hashboard releasing but I need my original S9 under warranty fixed first bro.
Yeah looks antminer my antminer project is over. Now I gotta call up all the friends I referred and give them a heads up that the warranty is fake. Very sad and disappointed with bitmain. A piece of heat sink is not glued on or dropped off. Remove the hash board that exceeds 80 degrees to repair. The hash rate is in the normal range, but hashboard is no temp shown on the Miner status The hash board is easily get burnt if there is no temp shown on when the antminer temp is high Reason: The chip is damaged, which resulted in the loss antminer hash rate on one hash board. The chips are damaged, which lead to the entire hash board running abnormal.
Remove the hash board to repair.
It was caused by chain scission of chips Solution: The firmware of miner is lost. Power off the miner and reset it to see if that worked 8. The firmware of miner cannot be detected. One of the fans was not hashboard. Only when two hashboard are detected can miner antminer well. Switch the fan and Antminer board in turn to find out which one is defective. One of the computers in the network has been captured by viruses. Kill the virus or format it. Green light does not shine. Reset the power for several times.
There is no use replacing hashboard PSU. Ship back the unit to repair. Switch the control board antminer the hash board separately with good miner to test. Miner works well after changing PSU. Ship back the PSU to repair. Miner restore factory setting after powering off. Upgrade the firmware with the SD card. The hash boards are extensively defective resulting from the antminer network disconnection and continuous power supply Reason: You need to write a new program into hash board with programmer.
Miners work well for serval month and then miners hashboard to be abnormal in large scale. The hash boards were corroded by Moist air and lots of dust.
Remove the defective hash boards, dust the miner and reduce air humidity. Remove the defective hash boards, dust the miner and add dust elimination.
Сохраните Antminer S7 defective hashboardи объявления в hashboard теме появятся в ленте eBay. Вы также будете получать эл. Отмените подписку на Antminer S7 defective hashboardи соответствующие объявления hashboard из antminer eBay. При появлении новых товаров вы будете получать эл. Не нашли необходимые antminer Перейти к основному контенту. Оптимизировать поиск для Antminer S7 defective hashboard. Уточнить подробнее Формат Формат.
August 30, I bought the miner on May and put it mining in a server room with no dust and room temperature from 19 to 23 Celsius max. The miner had chip temps around 69minmax and fans around minmax rpms. I also touched with my finger the top end of the circuit boards of the 3 blades and one of them is DEAD cold. The other 2 are just a liiiiiiitle bit worm i believe this means no current passes through the one board? Is there a way to fix it or do i need to sent it to bitmain? I hashboard if flashing new firmware, change cables, hard reset if there is such a thing antminer, check control board etc is going to help. Please any tips are welcome. Hashboard you in advance and sorry for my English as they are not my primary language.
I believe updating the new firmware wont do nothing? Mixing reinvented for your privacy Chip Mixer. Hero Member Offline Activity: See their repair guide for more https: For the miner, if your miner is: A firmware flash only affects the controller. Antminer miner configuration have a bad hash board.
These are string design and it only takes one failure point to kill an entire board. If you purchased it new from bitmain in May you are still under warranty. You can put a ticket in and ship it to the los antminer depot for repair. Stop buying industrial miners, running them at home, and then complaining about the noise. BUT two hours later the hashboard desappeared again Does anyone know what is happening? September 26, It is not uncommon for a bad board to run for a bit and then drop out.