Clarion-caraudio.ru

C1 antminer

Quoted figures depend on your PSUs efficiency, the ambient temperature and the accuracy of the power meter. C1 mines are stand alone and do not require a proxy server or external controller. Setup consists of installing the water pump, radiator, antminer the coolant, connecting a PSU and an Ethernet cable. Skving technology is used to design New-Style water cooling block. This allows for a large heat-transfer area, which keeps the PCBs exceptionally cool. Four hashing PCBs with 16 BM chips per antminer u2 настройка cgminer are mounted to the both sides of two aluminum water cooling blocks, which are mm-long, mm-high and 13mm-thick.

Each water cooling block contains 24 water channels for efficient heat transfer. Tape it up for safety. The power supply will now be controlled by its switch on the rear socket.

c1 antminer

Noise levels are reasonable considering the W of heat being removed with a single fan. If construction instructions antminer following correctly, the fan should be in a pull arrangement. It is noteworthy that the end closest to the fan may become very hot antminer the touch extremely hot to the touch including the handles during operation, so please be careful during handling and maintenance. Step 1 We are going to start by preparing the radiator. This is a high density, mm aluminium radiator with three mm fans installed already. Screw the two screws in to hold the 51mm in place, being careful not to damage the plastic threads.

Step antminer Unscrew the two bottom antminer screws on each end fan and discard the washers. Place the radiator stands between the antminer l3 купить в наличии grill and radiator on each side. Use the same screws as you removed to screw through the fan grill, radiator stand and into the radiator. Locate the two short, silver screws and screw in the other side of the radiator stand antminer the radiator.

Step 3 Next we will prepare the pump. This is a 15W pump with 3m of head pressure and litres per hour of flowrate. Locate two fittings and screw them into the brass inserts. Step 4 Locate the tubing and cut three pieces from it, two of 70cm length and one of 40cm length. You can do this with standard scissors but try and make the ends flat. Step 5 The C1 is next to be prepared. First open the antminer by unscrewing the 5 screws on each side.

ANTMINER C1 Discussion and Support Thread

Locate the cable harness and plug in the 3 pin fan header to the header closest to the end with the fan. Unscrew the two black caps from the C1. A small amount of fluid may leak when you unscrew these caps. There are then various different ways to do the next stage depending on what type of fittings you have. Step 6a - Standard Fittings Screw in a fitting, slightly further than hand tight. Place a spring clamp on the 40cm length antminer tubing, and work it 10cm down the tube so it is out of the way.

Then push the tube over the end of the fitting until the tube hits the end of the fitting. This may be difficult or easy depending on the profile of that length of tubing. Slide the spring clamp over the fitting until it is squeezing the tubing over the smooth section of the fittings. Repeat for the other side using one of the longer sections antminer tubing.

Join the other half of the quick release connector to mate the pair. Step 6c - Quick Release Barb Fittings Follow Step 6 a above but using antminer 8cm lengths of tubing instead Place a spring clamp over the exposed length of tube and bitcoin asic miner antminer s1 что это it down out of the way. Push one end of the quick release fitting into the tube.

Step 7 Connect the short tube from the C1 to the outlet [the bottom, black fitting] on the pump using the process in Step 6 a.

Antminer C1 Standard | clarion-caraudio.ru

Latest stable version of Bitcoin Core: Hero Member Offline Activity: October 31, Liquid Cooled Miner Antminer It is not only cool, but it is cool. Only Available at bitmaintech. Just Go to Hashnest. Hero Member Offline Posts: Prepare the watercooling for the miner. Plug in the eight PCI-E cables to the miner. Plug in antminer ethernet cable from the AntMiner to you router. Power on the power supply using its switch at the back.

Bitmain Antminer C1 is a New 1 THS Water Cooled Bitcoin ASIC Miner - Crypto Mining Blog

If not then change it to 1, this is just temporary. Login using "root" as both the username and password. Using a browser, navigate to your router and find the IP it has assigned the C1 and navigate to that IP. Enter your pool information in antminer below format.

c1 antminer

Navigate to antminer page "Miner Status" to check mining has started. You can then change your блок питания для antminer subnet back to whatever you are used to using. Unplug your computer from all internet sources. Plug in an ethernet cable from the AntMiner to your computer. Click on "Internet Protocol Version 4" and click properties.

Select "Use the following IP address" and enter the following: Restart the configuration instructions as above. Almost all "x" on one row of "Chips" - A hashing board may be mispowered or faulty. Recheck your cabling and PSU. How do I change the login password? Enter the current password and enter your new one twice. What is the SSH login? Can I turn the beeping off when the miner stops mining? I can connect to the AntMiner but its not hashing? What temperatures should I aim antminer

Похожие статьи:

  • Antminer s5 scrypt
  • Antminer u3 63gh для чего
  • Скачать antminer для windows
  • Antminer not hashing
  • Innosilicon a5 dashmaster x11 asic miner

  • Рекомендуем почитать:

  • майнер antminer s5 купить
  • gtx 1070 gaming x 8g mining
  • antminer s9 купить
  • Clarion-caraudio.ru - 2018 (c)